![]() I have the Xbox in 'energy saving' mode which is supposed to fully power down the XB1 on shutdown as opposed to the 'instant off' mode which goes into standby. There are tonnes of solutions to this problem, just work through the list and you'll find what works for you The GUS404 has a 5V USB port on the front that I connect to a wall wart - I use this rather than a USB hub. There is zero need to go through a complicated authentication routine, it's just plug-and-play. To use a different console, I simply swap the controller and toggle the switch to that console. T1 plugs into the USB switch, the switch outputs to 360, PS3, PS4 and XB1. ![]() When you're sitting at the blinking AU, toggle the USB switch until you get back to the XB1 and it should authenticate.Ī USB switch is my solution and it works flawlessly. Now that being said, you can hot-swap a Titan + Xim on a booted XB1 by using a USB switch such as an IOGear GUS402 or GUS404. Alternately, connect the T1 PROG port to a PC (or a USB wall charger) to add more juice to the loop at the T1. There's also a chance that the T1 when paired with Xim4 requires a touch more power than the console can supply to your m/kb/controller, in which case a powered USB 2.0 hub can help. Anker brand USB cables and Titan Connection Kits are highly recommended. If you continue to have AU problems, try removing the XB1 controller battery to reduce power drain and change the USB cable from the controller to the Xim, in case it's not the best quality cable. Note that Speed Up settings should be disabled, as should Cross Console something or other on the next Gtuner tab (I'm not at home and don't have access to my gear) when pairing a T1 with a Xim to avoid USB sync problems (purple lights). T1 should authenticate the Xim and off you go. Turn ON XB1 using the console power button. Don't use sleep mode, it needs to be shut down completely. This authenticated the XB1 controller when connected to the T1 however when I connected an Xbox 360 controller to the Xim and Xim to T1 it flashes AU but more rapidly than usual. This gets AU from connecting whilst powered off right up until the XB1 is fully booted up and continues to flash AU slowlyĢ) Authenticate the Titan One with the console using a Xbox One controller with the cable ģ) Remove the Xbox One controller from the Titan One Ĥ) Connect a PS3 or a wired Xbox 360 or a PS4 controller on XIM4 back USB port T1 will report 0.ĥ) Unplug XB1 controller from T1, plug controller into Xim4.Ħ) Plug Xim4 into XB1 - T1 will report AU, before changing to 0. Has anyone got any experience with Xim+T1 with the Xbox One X with the latest versions of Xim 4 and T1 firmware? as I imagine it could be an Xbox One X compatibility issue either with the console or controller when using Xim+T1.Ĥ) Authenticate with XB1 controller. The only other change I have made since changing from PS4 is the T1 firmware, I updated it to Ver 3.60, however because I didn't have an Xbox before I did the update I can't verify if that caused the issue or not. I have tried disabling all in frame in/out settings and had the same issue. Gtuner settings have been restored to factory defaults and the output protocol is set to automatic, I have also tried Xbox One protocol. Again all worked fine on PS4, I even just connected up my PS4 again to test it and all works fine. The controller micro USB cable must be okay as must the Xim to T1 micro USB cable as they both work when each device is tested individually until the T1 is used with the Xim. The controller works on it's own straight into the Xbox, and the controller to the T1 works when used without the Xim. The Xim works fine on it's own with the controller/mouse/kbd connected to the Xim. I tried all XB1 USB ports, I am just getting AU flashing on the T1,the X1 controller vibrates to say it has been detected but the Xbox logo does not light up to say it's authenticated with the XB1. I unplugged from the wall and did a cold boot with all connected, still the same issue. I am having problems when trying to use the my Xbox One X with Xim 4 and Titan One, when trying different methods the T1 is just constantly displaying AU.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |